Ring magnets for coaxial and circular magnetic interfaces.

Name: Custom Ring Magnets
Brand: Elite Magnets

A general ring product family covering flat rings, thick rings, sleeves, segmented constructions, and reviewed pole patterns without splitting each material, magnetization, or application into a duplicate product page.

Request a Quote for Ring Magnets

Back to Products

Rare-earth ring magnet components prepared for a circular magnetic interface

Product familyFlat rings, thick rings, sleeves, and segmented circular variants

Common materialsSintered NdFeB, sintered SmCo, or bonded rare-earth material where suitable

Common custom optionsOD, ID, length, wall thickness, pole pattern, coating, concentricity, and marking

Typical usesMotors, encoders, pumps, couplings, speakers, sensors, and circular assemblies

Product

Ring construction is the product; pole pattern and process are specifications.

Marketplace catalogs often split rings by material, magnetization, or end use. To prevent duplicate products, this page keeps solid rings, sleeves, segmented rings, and multipole variants under one primary circular family. The drawing then defines the exact construction, material, field pattern, and assembly state.

Review ring geometry, magnetization, assembly, and inspection capabilities

Natural fit for shafts, sleeves, and coaxial assemblies

Axial, diametrical, radial, or multipole routes

Solid, bonded, or segmented construction options

Common sourcing situations

Outer diameter, inner diameter, and axial length define the primary form.
The magnet surrounds or aligns with a shaft, sleeve, sensor, or circular working gap.
A solid ring, molded ring, or segmented construction can be compared within one product family.
Axial, diametrical, radial, or multipole magnetization can be referenced to the part.

Details to confirm before production

Thin walls and brittle material routes need realistic concentricity, wall, and handling requirements.
Radial and multipole patterns depend on fixture feasibility and a clear physical reference.
Segmented rings add gap, polarity, retention, and assembly-sequence requirements.
Working field must be evaluated at the real radial or axial gap and assembly state.

Specification

Define geometry, construction, and pole pattern as one circular interface.

A useful ring specification combines OD, ID, length, wall thickness, concentricity, material, coating, construction, magnetization, angular reference, working gap, and inspection. Multipole and segmented variants remain ring magnets rather than separate overlapping product families.

Common information used to define a ring magnet.

Geometry	Outer diameter, inner diameter, axial length, wall thickness, concentricity, runout-sensitive interfaces, and datums.
Construction	Solid sintered ring, bonded ring, sleeve, segmented ring, or assembly-dependent route subject to feasibility review.
Magnetization	Axial, diametrical, radial, multipole, pole count, angular reference, and magnetized or unmagnetized delivery.
Surface and assembly	Coating, bonding, shaft or housing relationship, sleeves, gaps, retention, cleanliness, and marking.
Inspection and packaging	OD, ID, length, concentricity, coating state, polarity, pole map, waveform, orientation, and protected packing.

Technical Data

Generic ring magnet product reference.

The fields below reflect common product-listing options. They organize a sourcing conversation but do not promise stock sizes, grades, tolerances, output, pole patterns, or delivery terms.

Specification field	Common catalog options	Confirm for production
Dimensions	Outer diameter × inner diameter × axial length	Finished dimensions, wall thickness, concentricity, datums, and coated state
Material	NdFeB, SmCo, or bonded rare-earth route	Grade, operating temperature, load line, geometry, and environment
Construction	Solid ring, sleeve, segmented ring, or bonded molded ring	Output, geometry, tooling, assembly gaps, retention, and volume
Magnetization	Axial, diametrical, radial, multipole, or drawing-defined pattern	Pole count, polarity, angular reference, delivery state, and test position
Surface	Nickel, epoxy, zinc, passivation, or application-reviewed protection	Exposure, coating build, bonding, edge coverage, and assembly fit
Supply condition	Individual rings, matched segments, orientation-packed sets, or assembly-ready components	Quantity, marking, packaging, cleanliness, and acceptance documents

This is generic catalog information. Final capability and acceptance are confirmed after drawing, construction, material, magnetic, coating, and application review.

Common catalog variants

Common circular variants remain part of one ring product family.

Magnetizing tool used to prepare a defined ring magnet pole pattern

Flat and thick rings

Solid circular parts defined by outer diameter, inner diameter, and axial length.

Precision machining environment used to review ring geometry

Sleeves and long rings

Extended axial forms used around shafts, rotors, pumps, sensors, and coaxial assemblies.

Precision inspection for ring magnet dimensions and concentric interfaces

Segmented and multipole rings

Circular systems whose construction or pole pattern is specified as an attribute of the ring product.

Application examples

Common applications for circular magnetic components.

Motion-control context using a circular magnetic interface

Motors and motion control

Rotor, stator, and coaxial magnetic interfaces reviewed around pole pattern, air gap, speed, and temperature.

Motor research context for ring magnet performance review

Encoders and sensors

Ring targets with defined pole direction, pole count, angular reference, working distance, and measurable response.

Industrial system context for ring magnets and circular assemblies

Pumps and couplings

Circular components used across sleeves or sealed gaps with geometry, exposure, and retention reviewed together.

Engineering guides

Use the same engineering checks across every product family.

Material, coating, magnetization, tolerances, and inspection remain product attributes. Confirm them against the drawing and application instead of creating another duplicate product category.